Game box

I made a box to hold a laser cut Carcassonne set that I have previously made.

I used the mitre saw to cut mitre joints into a piece of wood. Then I used the circular saw to cut slots for the top and bottom multiplex boards. After gluing the box together I used the circular saw to separate the lid and chiselled out holes for the fabric hinges. These were glued in and covered with some of the removed wood. Finally I added some dividers to organise the pieces inside the box and laser engraved a logo which was inlaid in the lid.

Mike

A Lazy Susan / Chessboard

I made myself a Lazy Susan (turntable) with a veneered chessboard on the surface. It is great for board games and serving food.

The end result

I used a variety of tools at the Makerspace to complete this project. This was the first time I have used veneer in a pattern on a surface.

The top and bottom pieces of wood were roughly cut into circles. Then made round and channels added using a router. Dividers were made on a scroll saw and holes drilled for marbles. A bolt holds the top and bottom together. Veneers were cut into squares and the edges sanded before applying them to the top. More veneer was added to the top before sanding it flat. After a few repairs to the top surface the turntable was varnished and felt feet were applied to the bottom.

Mike

Laser Cut Icarus

The first week of April we cleaned and realigned the optics of our Lasersaur. It works like new now. The first trial I did was an Icarus Automaton. It’s based on a Cupid Instructable by robives.com . My pupils at school are working on an Icarus/Daedalus assignment an I thought: “Why not make an Icarus myself”.

Edited design of the Cupid by Robives
The finished automaton

And this is how it looks, when it moves
But of course a trail also brings some flaws to light. The Laser cutter still needs some tweaking of the optics… as you can see on the photo’s of the front and back of the cut plywood for my automaton

The front, it seems to have worked properly
But on the flip side, you can see that the laser hasn’t totally cut through all parts.

I worked with plywood 3mm with a base coat white paint.
The lasersaur was set to speed 1000 at 40% powerit worked good on most places, but there is a zone close to 0 that loses power through alignment problems. Were almost there though… And my project was finished in no time!

Reclaimed Jatoba wood flooring table

This extendable table has been built with reclaimed flooring wood. This table has been built in the course of a year in the space.

(finished product first)

Jatoba built, reclaimed wood and 60s look.



colorful coffee table

This is my coffee table made from American walnut (gray), Oak (white) and Padouk (red). These colors are natural. This Padouk has a rare grain pattern, the white ‘clouds’ are sap-wood, which are normally not mixed with the older red tinted wood. I love finding these rare woods and combining them into beautiful tabletops. The table is a simple and lightweight design, finished with Skylt polyurethane finish.

Flame heater lamp-André BJM Weijermars-

De Nederlandse overheid promoot gasvrij koken en verwarmen, hier is t’ie dan… de aardgasvrije Flame heater!

De Flame heater lamp simuleert actieve vlammen in een koker. De lamp is 2 meter hoog en bestaat uit 5 strips van elk 60 individueel adresseerbare LEDs die worden aangestuurd door een Arduino Nano kloon. De 5 strips zijn verticaal rondom bevestigd aan een mast van een surfplank. De code is een bewerkte versie van de oorspronkelijke code ‘Fire2012 by Mark Kriegsman, July 2012’.

Klik het plaatje en het filmpje opent in nieuwe tab Click the graphic and the video opens in new tab

Dutch goverment promotes gas-free cooking and heating, so here it is! The natural gas-free Flame heater.

The Flame heater lamp simulates active flames in a sleeve. The lamp is 2 meters high and consists of 5strips of60 individual addressable RGB LEDs each and is controlled by an Arduino Nano clone. The 5 strips are vertically mounted on around a surfboard mast. The code is an adapted version of the original ‘Fire2012 by Mark Kriegsman, July 2012’.


Klein kistje met gravering

Deze kleine kistjes van 3mm triplex zijn gemaakt met een kant en klaar gekocht bestand van www.librarylaser.com
Er zit een mooie klik constructie in met een flexibel palletje.
Ze zijn ook stapelbaar.
De tekeningen voor de zijkanten heb ik zelf getekend aan de hand van foto’s in Inkscape.  Het zijn snijlijnen op laag vermogen, want de Lasersaur heeft helaas geen aparte graveermodus.
Een bescheiden demo hoe een lijntekening te maken in Inkscape  staat op de planning. Laat het maar weten als je interesse hebt.

Millie

 

Snijwerk in de lasersauervoorbeeld kistjesGestapelde kistjes

Nelson Bench by Quinten de Korte

This beautiful George Nelson inspired bench is the first big project of our new member Quinten de Korte. The bench is made out of reclaimed Mahogany and Oak. Which was collected from a home renovation.

Nelson_bench_by_Quinten_de_korte
Bananaforscale

This will be the first of many beautiful furniture pieces made @mls by Quinten de Korte.

Nelson_bench_by_Quinten_de_korte
So many Clamps

Close up of the leg joinery

Nelson_bench_by_Quinten_de_korte
Only thing left to do is some Danish Oil

Inspired? Come and join us. Make your ideas come to life @MakerSpaceLeiden